NIDEC COMPONENTS logo
NIDEC COMPONENTS logo

LIST

×

×


Products

Distributor

EU-English

×

Rotary encoder REC16 / RES16

  • REC16&RES16
    REC16&RES16
  • REC16&RES16
    REC16&RES16

Contact Us

●To make a purchase, contact Distributors, or use e-commerce below.
SALES CHANNEL  ;Check our Distributors.
SALES CHANNELClick here to check our Distributors.
To the Rotary encoder“REC16 / RES16 series” page on the RS Components online shop
To the Rotary encoder“REC16 / RES16 series” page on the DigiKey online shop
To the Rotary encoder“REC16 / RES16 series” page on the Mouser online shop

New 50P/R clickless type lineup

 

FeaturesFeatures
  • High resistant to electrostatic noise by using a plastic shaft

  • Compact size of 16 mm square

  • With mechanical ON/OFF push switch

  • Long life

  • RoHS compliant

PART NUMBER DESIGNATION

REC16A25-201-C

Series name

REC:With click
RES:Without click

Push switch function

A:With push switch 
B:Without push switch 

Resolution (P/R)

25, 50

Output phase

2:“A” & “B”

 

 

Snap-in holder

C:Yes

Blank:No

 

LIST OF PART NUMBERS

Part numberResolutionClickPush switch functionSnap-in holder
REC16A25-201 25 (P/R) With Click Yes No
REC16A25-201-C Yes
REC16B25-201 No No
REC16B25-201-C Yes
RES16B25-201 Without Click No
RES16B25-201-C Yes
REC16A50-201 50 (P/R) With Click Yes No
REC16A50-201-C Yes
REC16B50-201 No No
REC16B50-201-C Yes
RES16B50-201 Without Click No
RES16B50-201-C Yes

Electrical characteristics

Input voltage 5 VDC ± 5 %
Input current 30 mA maximum
Output wave form Square wave
Output phases A, B
Resolution (P/R) 25, 50
Phase difference of outputs A & B 100 μsec minimum  Refer to "OUTPUT"
Maximum frequency response 100 Hz
Output signal“1 (High)” + 4.5 V minimum
“0 (Low)” + 0.5 V maximum
Light source LED

OUTPUT

◆Click spot for 25P/R

※The click spot is located somewhere outputs A & B are at Lo level.

◆Click spot for 50P/R

Mechanical characteristics

Starting torque 1.18 mN·m ± 0.78 maximum (12 ± 8 gf·cm)
RES:Without click
Click torque Please refer to Table 1 below.
〈REC:With click〉
Click number 25, 50
Shaft loading (Pull-push) 19.6 N maximum (2 kgf)
Switch operation force 7.85 N ± 2.94 N (800 ± 300 gf)
Switch stroke 0.5 mm
Rotational life (Mechanical) 1 million cycles
Shaft loading
(When mounting)
Radial 4.90 N maximum (500 gf)
Axial 2.94 N maximum (300 gf)
Net weight Approx. 10 g
Strength of tighten screw 1 N·m {10.2 kgf·cm} maximum
〈Click torque〉----Table 1
Part numberClick torque
mN·mgf·cm
REC16A25 6.87 ± 3.43 70 ± 35
REC16B25 6.87 ± 3.43 70 ± 35
REC16A50 4.91 ± 1.77 50 ± 18
REC16B50 3.43 ± 1.77 35 ± 18

Switch characteristics

Maximum contact rating DC15 V, 20 mA
Contact resistance 200 mΩ maximum(Initial value)

Note) Manual setting only.

Environmental characteristics

Operating temp. range 0 ~ 50 °C
Storage temp. range – 20 ~ 80 °C
Protection grade IP40

RELIABILITY TEST

Test itemTest conditions
VibrationPower OFF Amplitude : 1.52 mm or 98.1 m/s2 (10 G) whichever is smaller.
10 ~ 500 Hz excursion 15 min/cycle, 8 cycles each for X, Z, directions.
ShockPower OFF 3 times each in directions (X, Z) at 490 m/s2(50 G), 11 ms.
High temperature
exposure
Power OFF 80 °C  96 h (To be measured after leaving samples for 1 h at normal temperature and
humidity after the test.)
Power ON 50 °C  96 h
Low temperature
exposure
Power OFF − 20 °C  96 h
Power ON 0 °C  96 h
HumidityPower OFF 40 °C   Relative humidity 90 〜 95 %   96 h(To be measured after wiping out moisture and leaving samples for 1 h at normal temperature and humidity after the test.)
Thermal shockPower OFF To be done 10 cycles with the following condition
(To be measured after leaving samples for 1 h at normal temperature and humidity after the test.)
80 °C 0.5 h、− 20 °C 0.5 h

OUTLINE DIMENSIONS

Unless otherwise specified, tolerance: ± 0.4 (Unit: mm)

  • Without snap-in holder
    Part Numbers: REC16A25-201, REC16B25-201, RES16B25-201 REC16A50-201, REC16B50-201, RES16B50-201
  • With snap-in holder
    Part Numbers: REC16A25-201-C, REC16B25-201-C, RES16B25-201-C, REC16A50-201-C, REC16B50-201-C, RES16B50-201-C
  • Accessories

  • Mounting hole dimention (Tolerance : ±0.1) (Board thickness t = 1.6)

PIN ASSIGNMENT

Pin No.Without switchWith switch
1 Power 0 (V) Power 0 (V)
2 Output “B” Output “B”
3 NC For Switch
4 NC For Switch
5 Power ⊕ Power ⊕
6 Output “A” Output “A”

OUTPUT CIRCUIT

KNOB FOR SETTING ENCODERS

  • The knobs are sold separately as an optional item.
    You can choose gray or black color.
    The hexagon socket head screws are attached. (2 pieces)

●The above contents and descriptions are subject to change without notice. 

Products

×

page top