Potentiometers CP2HX
-
●To buy this product, please contact Sales Reps, Distributors.
Miniature Drip-proof Dual Output Touchless Type Hall-IC Rotary Angle Sensor
FeaturesFeatures
- Thin & Touchless (No shaft) Type
- Since the input shaft is separated from sensor housing, it is suitable for the application that needs low torque and also easy to mount because you do not need to make the input shaft hole on the sensor mounting plate.
- Effective Electrical Travel : ±180°
- Absolute Linearity : ±2 %FS
- Output Signal: Voltage Ratio/ PWM
- Dual Output (6 wires)
- Water drip proof : IP67
Electronics Characteristics
| Part Number | CP2HXCxxxRx | <CP2HXPxxxRx | CP2HXCxxxPx | CP2HXPxxxPx |
|---|---|---|---|---|
| Effective Electrical Angle | ±180° (Option：± 45°, ± 90°） | |||
| Output Range | Ratio Output 10 ∼ 90 %Vin | PWM 10 ∼ 90 %Duty | ||
| Absolute Linearity | ± 2 %FS (When Gap is recommendation value） | |||
| Input Voltage | 5±0.5 VDC | |||
| Load Resistance | 10 kΩ Min. /1ch | |||
| Current Consumption | 10 mA Max. /1ch | |||
| Insulation Resistance | Min. 100 MΩ / 50 VDC | |||
| Resolution | 12 bit (0 ∼ 100 %Vin) | |||
| Hysteresis | 1.0 %FS | |||
| Temp.Characteristics -40 ~ 85 ℃ (25℃ std) |
± 1° | |||
| Dual Output Difference | OUT1+OUT2: 100±1 %Vin | OUT1+OUT2: ±1 %Vin | OUT1+OUT2 :100±1 %Vin | OUT1+OUT2: ±1 %Vin |
Mechanical Characteristics
| Total Mechanical Angle | 360 continuous |
|---|---|
| Net Weight | Appox.30 g |
Environment Characteristics
| Life Cycles | Mechanical unlimited | |||||
|---|---|---|---|---|---|---|
| Operating Temp. Range | -40 ~ 100 ℃ | |||||
| Storage Temp. Range | -40 ~ 100 ℃ | |||||
| Vibration | 200 m/s², 5∼500Hz 10 min, 3 axis 2 hours (Room Temp.) | |||||
| Shock | 500 m/s², 11 ms, 3 axis 3 times (Room Temp.) | |||||
| EMS | 100 V/m, 1MHz ∼ 1GHz (ISO 11452-2, -3) | |||||
| ESD(Case to Each Terminal) | Contact Discharge ± 15 kV (IEC 61000-4-2) | |||||
| ESD(Between Each Terminal) | Contact Discharge ± 15 kV (IEC 61000-4-2) | |||||
| Protection grade | IP67 (Circuit part only) | |||||
Part Number Designation
| CP2HX | C | 360 | R | 1 | XX |
|---|---|---|---|---|---|
|
Series name |
Output C : Dual Output (Cross) Standard |
Electrical Angle ±180° : 360 (Standard) |
Output type R : Voltage Ratio |
Sensor part 0 : Sensor part Only |
Custom |
Output Characteristics
◆Cross Output (Standard)
◆Parallel Output (Option)
Schematic
・Red, white, black, yellow, blue and green indicate harness colors.
Outline Dimensions
(Unit: mm)
● Sensor Part
● Shaft Part (Model：MH01)
Note: If you require a custom shaft part, please contact us
Mounting
(Unit: mm)
①Sensor Part
②Shaft Part (Model：MH01)
Note: If you require a custom shaft part, please contact us
※Gap of Sensor Part and Shaft Part
Gap between Sensor Part and Shaft Part are recommened value of the table below. If Gap is out of recommendation value the specifications (Linearity, etc.) may be out of specifiations.
Mounting Recommendation Value
| Direction | Recommendation value |
|---|---|
| Z Direction | 1.5 mm (0.5 mm ∼ 3.5 mm) |
| X ⇔ Y Direction | ±0.5 mm |
Handling Instruction
- Please mating a pair of the sensor part and the shaft part (same serial numbers are marked) for being guaranteed the accuracy of this product.
- Please mount the sensor part and the shaft part just as this drawing dimension. Please the magnetic substance and the magnet are kept away from this product.
- This product uses the strong magnet. Please materials that are susceptible to magnetic force are kept away from this product.
- Use this sensor in the place where is protected from ESD.
- Do not connect other than above Schematic diagram.
Documents
- ●The above contents and descriptions are subject to change without notice.
