Pushbutton switch 8W-N
-
●To buy this product, please contact Sales Reps, Distributors.
Snap-in Pushbutton Switches
-
The 8W Snap-in Pushbutton switch is an 8R Soft Touch Pushbutton switch with a 12 mm square button and a
mounting frame. -
The panel cut-out dimensions are the same as the 8H series Lever & Rocker switcheswhich enables side-by-side mounting.
-
Buttons and mounting frames are available in 4 colors.
-
Silver or gold-plated contacts
-
Epoxy resin case UL94V-0 self-extinguishing epoxy.
-
Insulation between terminal and ground: 4 mm minimum.
-
Prevention of flux entry The epoxy resin seal on bottom of the switch helps prevent short-circuiting between poles ensuring high reliability
-
Insulation barrier: Insulation barrier design between poles helps prevent short-circuiting between poles ensuring high reliability.
Specifications
| Rating | Silver plated:3A 125VAC （Resistive load） Gold plated :60mA 30VDC max. （Resistive load） |
|---|---|
| Initial contact resistance | Silver plated:10mΩ max.（1A 2～4VDC） Gold plated:20mΩ max.（5mA 200μVAC） |
| Initial dielectric strength | 1,000VAC 1 minute |
| Initial insulation resistance | 1,000MΩ min. (500VDC） |
| Electrical life | 25,000 operations(50,000 operations:Gold plate） |
| Operating temperature range | －20℃～＋85℃ |
| Storage temperature range | －40℃～＋85℃ |
| Operating force | 8W102■－N－Z:2.94±0.98N 8W202■－N－Z:4.9±1.96N |
Part Numbering
| 8 | W | 1 | 01 | 1 | B | - | Z |
| Series code |
Actuator shape N:Standard P:Splash proof Y:Mustang R:Soft Touch W:Snap-in |
Number of poles 1: 1 2: 2 |
Switching function 01: ON-ON 02: ON-(ON) |
Terminal style 1: Solder 2: PC/Straight |
Contact material /Plating None：Bs+Ag or Cu+Ag/Ag B: Bs or Cu/Ni+Au C:Bs+Ag or Cu+Ag/Ni+Au |
Note ：Some combinations may not be available. Please check the "Tableof Part Numbers" for each series.
List of part numbers
| Part Number | Number of poles | Switching function | Terminal style | CAD |
|---|---|---|---|---|
| 8W1021－N－Z | 1pole | ON －（ ON） | Solder | |
| ★8W2021－N－Z | 2poles | ON －（ ON） | Solder | |
| ★8W1022B－N－Z | 1pole | ON － ON | PC Straight |
Outline Dimensions
Terminal Styles
PC Hole Layouts
Panel Cut-Out Dimensions
Panel thickness（with Mounting Frame） : 1 mm to 2.5 mm
Button and Mounting Frame Installation
※Specify part number of Button and Mounting Frame when ordering.
Standard Accessories
※Please specify the Button and the Mounting Frame when ordering.
Soldering Specifications
- Manual soldering
Device：Solder iron
①420℃ Max. 3 sec. Max. - Auto soldering
②The above-stated soldering conditions shall apply only to switches with straight terminals. Auto soldering is not possible with right-angle terminals.
Switches with right-angle terminals should be soldered manually according to the conditions specified in (1) above. - When putting the switches through an aging process after they were soldered onto the printing board or after installed into a complete end product, be sure to remove the buttons ofthe switches.,
Mounting
- Do not bend the terminals before mounting the switch on the PC board.
- After mounting the switch, do not place the device in such a way that the device weight will be applied on to the actuator of the switch.
- For switches with straight terminals, solder the switch on the PC board after fixing the switch on the panel with a nut.
Flux Cleaning
- Solvent : Fluorine or Alcohol type.
- 8A/B/C/D/E/F/J/S series are not washable. To wash the PC board, clean the soldering surface of the PC board
with a brush so that the switch is not exposed to the cleaning solution.
UL-Recognized, CSA certified Products
Packaging Specification
(Unit:mm)
Documents
Environmental Data
- ●The above contents and descriptions are subject to change without notice.
