Trimmer potentiometer CT-6
-
CT-6
-
CT-6
- ●To buy this product, please go to the following Online Web stores.
Low Cost General-Purpose Type
FeaturesFeatures
- RoHS compliant
- Various configurations to choose from
- Wide variety (14 types)
- “O” ring sealed and washable
- In this series, material data sheets ideal for REACH-SVHC
surveys etc. can be downloaded in chemSHERPA-AI format. - Download chemSHERPA-AI from the list of P/N below
Electrical Characteristics
| Nominal resistance range | 10 Ω ~ 2 MΩ |
|---|---|
| Resistance tolerance | ± 10 % |
| Power ratings | 0.5 W (70 °C) 0 W (120 °C) |
| Resistance law | Linear law（B） |
| Maximum input voltage | DC200 V or power rating, whichever is smaller |
| Maximum wiper current | 100 mA or power rating, whichever is smaller |
| Effective electrical angle | 220 ° (1 turn) |
| End resistance | 1 % or 2 Ω , whichever is greater |
| C.R.V. | 1 % or 3 Ω , whichever is greater |
| Operating temp. range | −55 ~ 120 °C |
| Temp. coefficient | 10 Ω ~ 20 Ω : ± 250 10-6/°C maximum 50 Ω ~ 2 MΩ : ± 100 10-6/°C maximum |
| Insulation resistance | 1000 MΩ minimum (DC500 V) |
| Dielectric strength | AC500 V, 60 s |
| Net weight | Approx. 0.51 g (CT-6EP, EW, ER, EV) Approx. 0.65 g (CT-6ES, EX, EH, EN) Approx. 0.92 g (CT-6EF) |
Mechanical Characteristics
| Mechanical angle | 260 ° (1 turn) |
|---|---|
| Operating torque | 2 ~ 20 mN·m {20 ~ 204 gf·cm} |
| Stop strength | 50 mN･m {20 ~ 204 gf·cm} minimum |
| Rotational life | 200 cycles [ΔR/R ≦ ± (2 Ω +3 %)] |
| Teminal strength | 10 N {1.02 kgf} minimum（Tensile strength） |
| Thrust to rotor | 10 N {1.02 kgf} minimum |
| Solderability | 245 ± 3 °C, 2 ~ 3 s |
{ }: Reference only
Environmental Characteristics
| Test item | Test conditions | Specifications |
|---|---|---|
| Thermal shock | −65 ~ 125 °C(0.5 h), 5 cycles | [Δ R/R ≦ 1 %] [S.S. ≦ 1 %] |
| Humidity | −10 ~ 65 °C (Relative humidity 80 ~ 98 %), 10 cycles, 240 h | [Δ R/R ≦ 2 %] |
| Shock | 981 m/s2, 6 ms ,6 directions for 3 times each | [Δ R/R ≦ 1 %] [S.S. ≦ 1 %] |
| Vibration | Amplitude 1.52 mm or Acceleration 196 m/s², 10 ~ 2000 Hz, 3 directions, 12 times each | [Δ R/R ≦ 1 %] [S.S. ≦ 1 %] |
| Load life | 70 °C, 0.5 W, 1000 h | [Δ R/R ≦ 3 %] [S.S. ≦ 1 %] |
| Low temp. operation | −55 °C, 2 h | [Δ R/R ≦ 2 %] [S.S. ≦ 2 %] |
| High temp. exposure | 120 °C, 250 h | [Δ R/R ≦ 3 %] [S.S. ≦ 2 %] |
| Immersion seal | 85 °C, 60 s | No leaks (No continuous bubbles) |
| Soldering heat | Flow soldering :260 ± 3 °C, 5 ~ 6 s, two times Max. Manual soldering : 380 ± 10 °C, 3 ~ 4 s |
[Δ R/R ≦ 1 %] |
Δ R/R: Change in total resistance
S.S.: Setting stability
Maximum Input Ratings
| Nominal resistance values(Ω) | Resistance code | Maximum input voltage (V) | Maximum wiper current(mA) |
|---|---|---|---|
| 10※ | 100 | 1.00 | 100 |
| 20※ | 200 | 2.00 | 100 |
| 50 | 500 | 5.00 | 100 |
| 100 | 101 | 7.07 | 70.7 |
| 200 | 201 | 10.0 | 50.0 |
| 500 | 501 | 15.8 | 31.6 |
| 1k | 102 | 22.4 | 22.4 |
| 2k | 202 | 31.6 | 15.8 |
| 5k | 502 | 50.0 | 10.0 |
| 10k | 103 | 70.7 | 7.07 |
| 20k | 203 | 100 | 5.00 |
| 50k | 503 | 158 | 3.16 |
| 100k | 104 | 200 | 2.00 |
| 200k | 204 | 200 | 1.00 |
| 500k | 504 | 200 | 0.40 |
| 1M | 105 | 200 | 0.20 |
| 2M | 205 | 200 | 0.10 |
The products indicated by ※ mark are manufactured upon receipt of order basis.
Part Number Designation
| CT-6 | E | T | A | 5 kΩ (502) |
|---|---|---|---|---|
|
Series |
Terminal pins E: Sn (Lead-free) |
Packaging form T: Taping (Ammo pack type) M: Magazine (Stick) Blank: Bulk in plastic bag |
Adjustment position P: Top adjustment S: Side adjustment W: Top adjustment X: Side adjustment R: Top adjustment H: Side adjustment V: Top adjustment N: Side adjustment F: Rear adjustment *Classified by pin position |
Resistance value (Resistance code) |
| Nominal resistance values | 10Ω*, 20Ω*, 50Ω, 100Ω, 200Ω, 500Ω, 1kΩ, 2kΩ, 5kΩ, 10kΩ, 20kΩ, 50kΩ, 100kΩ, 200kΩ, 500kΩ, 1MΩ, 2MΩ |
|---|
When ordering, please be sure to include the above nominal resistance value at the end of the part number in the table list below. *10 Ω item, 20 Ω item are made to order.
For resistance code, please refer to the Maximum Input Ratings table in the previous section.
List of Part Numbers
CAD and chemSHERPA-AI (a material data sheet ideal for REACH surveys, etc. / version: 2.09.00) can be downloaded from the popup for each P/N in the table below. *Need to log in to download.
| Part No. | Position | Packaging form | Packaging quantity | Remarks | Material data | CAD |
|---|---|---|---|---|---|---|
| CT-6ETP | Top adjust | Taping* | 1000 pcs./reel | The pin length of CT-6ETP and CT-6EMP is different from CT-6EP. | ||
| CT-6EMP | Top adjust | Magazine | 75 pcs./stick | The pin length of CT-6ETP and CT-6EMP is different from CT-6EP. | ||
| CT-6EP | Top adjust | Bulk | 50 pcs./pack | The pin length of CT-6ETP and CT-6EMP is different from CT-6EP. | ||
| CT-6EW | Top adjust | Bulk | 50 pcs./pack | - | ||
| CT-6ER | Top adjust | Bulk | 50 pcs./pack | - | ||
| CT-6EV | Top adjust | Bulk | 50 pcs./pack | - | ||
| CT-6ETV | Top adjust | Taping* | 1000 pcs./reel | - | ||
| CT-6EMS | Side adjust | Magazine | 75 pcs./stick | The pin length of CT-6EMS is different from CT-6ES. | ||
| CT-6ES | Side adjust | Bulk | 50 pcs./pack | The pin length of CT-6EMS is different from CT-6ES. | ||
| CT-6EX | Side adjust | Bulk | 50 pcs./pack | - | ||
| CT-6ETH | Side adjust | Taping* | 1000 pcs./reel | The pin length of CT-6ETH is different from CT-6EH. | ||
| CT-6EH | Side adjust | Bulk | 50 pcs./pack | The pin length of CT-6ETH is different from CT-6EH. | ||
| CT-6EN | Side adjust | Bulk | 50 pcs./pack | - | ||
| CT-6EF | Rear adjust | Bulk | 50 pcs./pack | - |
*
Taping: Ammo pack type
※
Taping and magazine specifications are not sold separately and must be purchased in taping or stick units.
Outline Dimensions
Environmental Data
- ●The above contents and descriptions are subject to change without notice.
